Via the Oz:
Jetstar pilots forgot landing gear
ROBYN IRONSIDE
AVIATION WRITER
@ironsider
![[Image: e5fb238f2374df9dd6d08fb2debb60cc?width=650]](https://cdn.newsapi.com.au/image/v1/e5fb238f2374df9dd6d08fb2debb60cc?width=650)
An Australian Transport Safety Bureau investigation has found a plane was forced to go around when an alarm alerted the pilots to the fact the landing gear wasn’t down. Photo: Marc McCormack
A Jetstar aircraft coming into land at Ballina Airport on the New South Wales’ north coast, was forced to go around when an alarm alerted the pilots to the fact the landing gear wasn’t down.
The A320 had already conducted one go around at the captain’s command because the aircraft was coming in too high and too fast for a stable landing.
An Australian Transport Safety Bureau investigation into the incident on May 18 last year, found on the second attempt at landing a “master warning” was triggered because the landing gear had not been selected “down”.
After another go around, it was a case of third time lucky with the aeroplane landing without further incident.
ATSB transport safety director Stuart Godley said the report noted that an incorrect aircraft configuration for landing was rarely the result of a single action of identifiable event.
“In this case a number of factors, such as distraction and limited use of aircraft automation, combined to result in the landing gear not being selected to down,” Dr Godley said.
“While highly undesirable, it should be noted that the aircraft’s warning system effectively alerted the flight crew to the problem and the crew responded promptly to the warning and initiated a second go around.”
The report came at an unfortunate time for Jetstar pilots who are preparing to stop work this weekend over stalled enterprise bargaining negotiations.
The airline claims the pilots want a 15 per cent immediate pay rise but the Australian Federation of Air Pilots said this was not true.
“Put simply, Jetstar have manufactured the alleged 15 per cent increase based on inaccurate and flawed costings of our non-salary claims, such as those claims relating to rostering and fatigue mitigation,” said AFAP executive director Simon Lutton.
He said pilots were seeking 3 per cent annual increases
Somewhat surprising, for what was seemingly downplayed by the Oz as a relative non-event, this article has garnered over 50 comments -
For a different take and IMO better summary of this clusterduck event here is Steve Creepy via Airlineratings.com ...
JETSTAR PILOTS FORGOT TO LOWER THE LANDING GEAR
By Steve Creedy December 10, 2019
![[Image: 500_jetstarairbusa320cnsrfimg-95071.jpg]](https://www.airlineratings.com/wp-content/uploads/uploads/500_jetstarairbusa320cnsrfimg-95071.jpg)
The pilots of a Jetstar A320 forgot to lower the landing gear as they approached Ballina airport in northern New South Wales and were forced to conduct a go around after they were alerted to the oversight by a master warning.
The aircraft operating a flight from Sydney in May, 2018, had already conducted one go-around after the captain decided its airspeed and altitude were higher than a normal approach profile.
The Australian Transport Safety Bureau found the flight crew did not follow the Jetstar standard procedures during the first go-around and this created distractions that contributed to the landing gear oversight.
READ: Storms and communications brought jets too close
In particular, the flaps remained at the Flaps 3 position during the visual circuit rather than the company standard of Flaps 1.
The first go-around was performed correctly by the first officer until the Jetstar A320 reached the circuit altitude of 1500ft.
Watch the ATSB video reconstruction of the incident:
Video: https://www.airlineratings.com/wp-conten...eb.mp4?_=2
As the first officer leveled the aircraft, it accelerated quickly towards the Flaps 3 limit speed and the FO called for approach mode to be activated to reduce the plane’s target speed.
Worried about a potential flaps overspeed, where the airspeed exceeds safe limits for the flap setting, the FO retarded the thrust levers to idle and by doing so de-activated the auto-thrust system and its protections.
“With Flaps 3 still set and 10-degree nose-up pitch altitude, the aircraft performance deteriorated, requiring intervention by the captain,’’ the ATSB said.
Other distractions affecting the crew included the fact the first officer was expecting a left circuit instead of a non-standard right circuit and had not been briefed about the change.
Adding to this was the handover of flight duties to the captain, the need to correct the flight path and the fact the captain continued to fly the aircraft manually, adding to his workload.
The captain elected to remain at Flaps 3, which investigators described as permissible and safe but not Jetstar’s standard configuration for a visual circuit.
“The operator’s sequence of configuring the aircraft for landing required the landing gear to be selected DOWN prior to the selection of Flaps 3,’’ The ATSB report said.
“As the captain turned on to the final approach during the second approach, he scanned the flight instruments, observed Flaps 3 already set and instinctively commanded Flaps FULL, which was the normal sequence from Flaps 3.
“The FO selected Flaps FULL but then also turned his attention to monitoring the aircraft’s flight path.
“As such, neither of the flight crew were aware that the landing gear had not been selected DOWN.”
Investigators said that because the pilots flew the second circuit at 1500ft, the Electronic Centralised Aircraft Monitor (ECAM) had not reset on the second approach and it did not display a landing memo at 950ft.
“The absence of the landing memo should have prompted the flight crew to perform the items of the landing checklist as a ‘read-and-do’ checklist,’’ it said.
“Had they read the required actions from the checklist, both the captain and FO would have been required to independently check and announce that the landing gear was down.
“This method should have effectively ‘trapped’ their error.”
When the landing memo did appear at 800ft, the crew were focused on intercepting the final approach path and performing radio calls and neither recalled seeing it.
“Both the captain and FO were subsequently alerted to the incorrect configuration for landing by a master warning message triggered at about 700 ft,’’ the report said.
The flight crew conducted a second go-around and landed without incident.
ATSB transport safety director Dr Start Godley said the incident highlighted the importance of adhering to standard operating procedures and correctly monitoring the aircraft’s approach.
“In this case a number of factors, such as distraction and limited use of aircraft automation, combined to result in the landing gear not being selected to down,” Dr Godley said.
“While highly undesirable, it should be noted that the aircraft’s warning system effectively alerted the flight crew to the problem and the crew responded promptly to the warning and initiated a second go-around.”
Jetstar said that as a result of the incident, the pilots attended debriefings with operations management and underwent specific simulator and line flying training related to the event.
Finally here is a link and safety summary off the final investigation report: https://www.atsb.gov.au/publications/inv...-2018-042/
MTF...P2
Jetstar pilots forgot landing gear
ROBYN IRONSIDE
AVIATION WRITER
@ironsider
An Australian Transport Safety Bureau investigation has found a plane was forced to go around when an alarm alerted the pilots to the fact the landing gear wasn’t down. Photo: Marc McCormack
A Jetstar aircraft coming into land at Ballina Airport on the New South Wales’ north coast, was forced to go around when an alarm alerted the pilots to the fact the landing gear wasn’t down.
The A320 had already conducted one go around at the captain’s command because the aircraft was coming in too high and too fast for a stable landing.
An Australian Transport Safety Bureau investigation into the incident on May 18 last year, found on the second attempt at landing a “master warning” was triggered because the landing gear had not been selected “down”.
After another go around, it was a case of third time lucky with the aeroplane landing without further incident.
ATSB transport safety director Stuart Godley said the report noted that an incorrect aircraft configuration for landing was rarely the result of a single action of identifiable event.
“In this case a number of factors, such as distraction and limited use of aircraft automation, combined to result in the landing gear not being selected to down,” Dr Godley said.
“While highly undesirable, it should be noted that the aircraft’s warning system effectively alerted the flight crew to the problem and the crew responded promptly to the warning and initiated a second go around.”
The report came at an unfortunate time for Jetstar pilots who are preparing to stop work this weekend over stalled enterprise bargaining negotiations.
The airline claims the pilots want a 15 per cent immediate pay rise but the Australian Federation of Air Pilots said this was not true.
“Put simply, Jetstar have manufactured the alleged 15 per cent increase based on inaccurate and flawed costings of our non-salary claims, such as those claims relating to rostering and fatigue mitigation,” said AFAP executive director Simon Lutton.
He said pilots were seeking 3 per cent annual increases
Somewhat surprising, for what was seemingly downplayed by the Oz as a relative non-event, this article has garnered over 50 comments -
For a different take and IMO better summary of this clusterduck event here is Steve Creepy via Airlineratings.com ...
JETSTAR PILOTS FORGOT TO LOWER THE LANDING GEAR
By Steve Creedy December 10, 2019
The pilots of a Jetstar A320 forgot to lower the landing gear as they approached Ballina airport in northern New South Wales and were forced to conduct a go around after they were alerted to the oversight by a master warning.
The aircraft operating a flight from Sydney in May, 2018, had already conducted one go-around after the captain decided its airspeed and altitude were higher than a normal approach profile.
The Australian Transport Safety Bureau found the flight crew did not follow the Jetstar standard procedures during the first go-around and this created distractions that contributed to the landing gear oversight.
READ: Storms and communications brought jets too close
In particular, the flaps remained at the Flaps 3 position during the visual circuit rather than the company standard of Flaps 1.
The first go-around was performed correctly by the first officer until the Jetstar A320 reached the circuit altitude of 1500ft.
Watch the ATSB video reconstruction of the incident:
Video: https://www.airlineratings.com/wp-conten...eb.mp4?_=2
As the first officer leveled the aircraft, it accelerated quickly towards the Flaps 3 limit speed and the FO called for approach mode to be activated to reduce the plane’s target speed.
Worried about a potential flaps overspeed, where the airspeed exceeds safe limits for the flap setting, the FO retarded the thrust levers to idle and by doing so de-activated the auto-thrust system and its protections.
“With Flaps 3 still set and 10-degree nose-up pitch altitude, the aircraft performance deteriorated, requiring intervention by the captain,’’ the ATSB said.
Other distractions affecting the crew included the fact the first officer was expecting a left circuit instead of a non-standard right circuit and had not been briefed about the change.
Adding to this was the handover of flight duties to the captain, the need to correct the flight path and the fact the captain continued to fly the aircraft manually, adding to his workload.
The captain elected to remain at Flaps 3, which investigators described as permissible and safe but not Jetstar’s standard configuration for a visual circuit.
“The operator’s sequence of configuring the aircraft for landing required the landing gear to be selected DOWN prior to the selection of Flaps 3,’’ The ATSB report said.
“As the captain turned on to the final approach during the second approach, he scanned the flight instruments, observed Flaps 3 already set and instinctively commanded Flaps FULL, which was the normal sequence from Flaps 3.
“The FO selected Flaps FULL but then also turned his attention to monitoring the aircraft’s flight path.
“As such, neither of the flight crew were aware that the landing gear had not been selected DOWN.”
Investigators said that because the pilots flew the second circuit at 1500ft, the Electronic Centralised Aircraft Monitor (ECAM) had not reset on the second approach and it did not display a landing memo at 950ft.
“The absence of the landing memo should have prompted the flight crew to perform the items of the landing checklist as a ‘read-and-do’ checklist,’’ it said.
“Had they read the required actions from the checklist, both the captain and FO would have been required to independently check and announce that the landing gear was down.
“This method should have effectively ‘trapped’ their error.”
When the landing memo did appear at 800ft, the crew were focused on intercepting the final approach path and performing radio calls and neither recalled seeing it.
“Both the captain and FO were subsequently alerted to the incorrect configuration for landing by a master warning message triggered at about 700 ft,’’ the report said.
The flight crew conducted a second go-around and landed without incident.
ATSB transport safety director Dr Start Godley said the incident highlighted the importance of adhering to standard operating procedures and correctly monitoring the aircraft’s approach.
“In this case a number of factors, such as distraction and limited use of aircraft automation, combined to result in the landing gear not being selected to down,” Dr Godley said.
“While highly undesirable, it should be noted that the aircraft’s warning system effectively alerted the flight crew to the problem and the crew responded promptly to the warning and initiated a second go-around.”
Jetstar said that as a result of the incident, the pilots attended debriefings with operations management and underwent specific simulator and line flying training related to the event.
Finally here is a link and safety summary off the final investigation report: https://www.atsb.gov.au/publications/inv...-2018-042/
Quote:Safety message
Unexpected events during approach and landing phases can substantially increase what is often a high workload period. Adherence to standard operating procedures and correctly monitoring the aircraft and approach parameters provides assurance that a visual approach can be safely completed. The selection of inappropriate auto-flight modes, unexpected developments, or any confusion about roles or procedures can contribute to decisions and actions that increase the safety risk to the aircraft and its passengers.
The ATSB SafetyWatch highlights the broad safety concerns that come out of our investigation findings and from the occurrence data reported to us by industry. Handling of approach to land is one of these priorities.
MTF...P2